SCSI命令中止,如何解决？

cyberian

IsaacZ 发表于 2012-7-16 17:06

                               
登录/注册后可看大图

【光盘刻录错误代码查询】List of ATAPI Error codes 【NERO日志告诉我们什么】

对过了，傍晚回来刻录又出现新的问题write error。。

log是
18:59:06        #24 SPTI -1135 File SCSIPassThrough.cpp, Line 214
        CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1135)
        CDB Data:   0x2A 00 00 00 00 00 00 00 20 00 00 00
        Sense Key:  0x03 (KEY_MEDIUM_ERROR)
        Sense Code: 0x0C
        Sense Qual: 0x00
        Sense Area: 0x70 00 03 00 00 00 00 0A 32 4D 03 0C 0C
        Buffer x190b0040: Len x10000
        0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
        0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
        0x00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
       
18:59:06        #25 CDR -1135 File Writer.cpp, Line 306
        Write error
        G: HL-DT-ST DVDRAM GSA-T40N

核对了http://www.cdr-zone.com/articles/atapi_error_codes_page_1.html地址的

也是**030C00    4 5 6 Write error

显示Write error  我迷茫了。

4. DMA Settings
Setting DMA mode:

Windows 95/98/ME Users

Right click on [My Computer] and select [Properties] from the menu. Click on [Device Manager], then click on [CD-ROM]. This will expand to show the CD drives on your system. Right click on a drive and select [Properties] from the menu. Click on the [Settings] tab and check that the [DMA] option is enabled. Repeat this procedure for the remaining CD drives.

Win NT/2000/XP Users

Right click on [My Computer] and select [Properties] from the menu. Click [Device Manager] on the [Hardware] tab, then click to open the [IDE ATA/ATAPI (hard disk) controllers] section. You will find: the Primary IDE Channel controller, Secondary IDE Channel controller. Complete the following procedure:

Right click on the Primary IDE controller and select [Properties] from the menu.
Select the [Advanced Settings] tab. Check that the [Transfer Mode] for both devices is set to [DMA if available].
Repeat this for Secondary IDE controller.


Note: In some cases older CD-ROM drives will not support DMA mode. In that case please set both devices to PIO mode.





5. Disc



Recording errors often occur when the disc is dirty, or has fingerprints or scratches. If an error occurred during test simulation (before actual recording), clean the disc. If you are getting recording errors, try the following.
Use a different blank, recordable disc.
Use a different manufacturer's disc.
Ensure the disc is clean before recording:
Remove all fingerprints, dirt, and dust from the shiny side of your disc using a nonabrasive cloth with a mild, nonabrasive soap solution.
Wipe the disc from the center to the edge of the disc.
Dry the disc completely.


Error during file verification
If an error occurred when the files were being verified, record the same files again using a different disc.


Read error when copying a disc
When copying a disc, if an error occurred while reading data from the original disc, the original disc may be scratched or dirty.
Try cleaning the disc.
Remove all fingerprints, dirt, and dust from the shiny side of your disc using a nonabrasive cloth with a mild, nonabrasive soap solution.
Wipe the disc from the center to the edge of the disc.
Dry the disc completely.
Try using a different source drive.
To change the drive you use to read your disc, click the Change button when asked to insert a source disc into your drive tray.
Select the drive you wish to use from the drop-down menu.
Insert your disc into the new drive.
Try using copying the disc using one drive as both the source and destination drive.
When you use your recorder to both read and write to your disc, B's Recorder GOLD creates an image file of the entire disc to your hard drive and then copies that temporary file onto your blank disc. This can be helpful if the drive you are using to read your original disc is slow or unreliable.

If the problem persists, contact the drive maker.





6. Drive
If you have tried Actions 1 through 5 above, there may be a problem with your drive. Contact the drive maker with details of the error code. If the 5th and 6th digit of the error code is 80 through FF, then the error code is maker unique. The descriptions of these error codes differ depending on the maker.

都试过去依然是写错误。会不会是现在换成 win7 的问题。以前用xp同样的威宝dvd-r刻录正常。
刻了20片没一片坏的。

IsaacZ

cyberian 发表于 2012-7-16 19:05

                               
登录/注册后可看大图

对过了，傍晚回来刻录又出现新的问题write error。。

log是

让你对照排查，你复制来做什么？